Skip to product information
  • Vetonek Radiador toallero de baño recto negro 480x480 mm

Radiador toallero de baño recto negro 480x480 mm

$78.30
$78.30 $88.11
You save 11% ($9.81)
Tax included. Shipping calculated at checkout.

Description

Este radiador toallero está diseñado para doble propósito, como calentador de toallas y calentador de espacio. Ayuda a que los baños se mantengan calientes, libres de moho y es adecuado para secar toallas grandes y albornoces largos mientras tanto. Gracias a la ayuda del sistema de circulación de agua caliente, que no utiliza electricidad, las toallas se secarán enseguida. El radiador toallero tiene 8 barras transversales de acero de 22 mm de diámetro y está pintado de negro. Las barras transversales son extragruesas y, por eso, producen más calor. La parte superior y la inferior están equipadas con entradas de agua para optimizar el flujo de agua. Es fácil de montar y mantener. La entrega incluye 1 radiador toallero, soportes de pared y tornillos.

  • Color: Negro
  • Material: Acero
  • Estilo: Recto
  • Potencia térmica nominal: 191 W
  • Dimensiones: 480 x 480 mm (ancho x alto)
  • Distancia entre centros de tuberías: 430 mm
  • Distancia entre la pared y el frente del radiador: 80 mm
  • Número de barras transversales: 8, con un diámetro de 22 mm
  • Para montaje en pared
  • La entrega incluye 1 radiador toallero, soportes de pared y tornillos
  • Nota: El radiador toallero calienta agua, no electricidad.
Se debe supervisar a los niños para asegurarse de que no jueguen con el aparato. Mantenga a los niños alejados del área de montaje. Precaución: Lea atentamente las instrucciones antes de usar y consérvelas para futuras consultas.

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.