Skip to product information
  • Ubbink Filtro de estanques BioPressure 18000 18 W

Ubbink Ponds filter BioPressure 18000 18 W

$346.32
$346.32 $389.78
You save 11% ($43.46)
Tax included. Shipping calculated at checkout.
Size
Color

Description

The BioPressure 18000 pond filter of the UBBINK brand, with UV-C Integrated Unit, guarantees to clean your pond quickly (in combination with the Ubbink recommended pump pump). This BioPressure filter can be used in ponds with a capacity of up to 18,000 liters (without fish). As the name implies, the water passes through the filter under pressure. This means that it is possible to pump water at a higher level, for example, for a waterfall or stream, but also that the filter cannot overflow or explode even when installed at a lower level or below the water surface level . The pressure filter can support a pressure of 0.49 bars. The special seal guarantees the integrity of the filter even in very demanding conditions. The filter with layers avoids blocking and mechanically eliminates the dirt particles of the water. The filter can be cleaned quickly, even while it is in operation, with the practical and simple tap to empty wastewater.

  • Food: 230 V ~, 50 Hz
  • Filter unit capacity: 25 L
  • Pressure load: maximum 0.49 bar
  • Current water outlet up to 1.50 m high
  • UV-C power after approximately 5000 hours: 85%
  • Water input/output diameter: 25 mm
  • Filter medium: special filter mattress of several levels
  • Cleaning function without opening the case
  • Recommended for ponds with a maximum capacity of 18,000 L
  • It works with a water temperature between + 5 ° C and + 35 ° C
  • Maximum particle dimensions: 25 mm
  • UV-C lamp type: PL-L 18 W
  • Cable length: 4.5 m
  • Clip closure
  • Protection class: I
  • IP classification: IP44
  • The delivery includes:
  • 1 x BioPressure II pressure filter with UV-C integrated device
  • 1 x universal hose nozzle (40-32-25-19 mm), transparent
  • 2 x Universal Hose (40-32-25-19 mm), Black
  • 3 x Sealing joints 1 ½ "
  • 1 x threaded ring with sealing lid (glass)

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.