Skip to product information
  • "Botella de 500 ml de detergente anti-verdín ALGACID de la marca FILA. Elimina algas, moho, líquenes y suciedad en piedra, ladrillo, cemento, y otras superficies. Ideal para exteriores, incluyendo paredes pintadas y hormigón. Presentación con pulverizador para fácil aplicación."
  • "Etiqueta de advertencia de peligro para ALGACID. Instrucciones de seguridad para el uso de hipoclorito de sodio, altamente tóxico para organismos acuáticos y con riesgo de causar quemaduras graves en la piel y ojos. Incluye pictogramas de riesgo químico y medidas en caso de contacto."

Anti-verdin detergent

11,40 €
11,40 €
Tax included. Shipping calculated at checkout.
Container

Description

Anti-Verdin Detergent File: Quick and effective exterior surfaces

What is it for?

The outdoor anti-verdin detergent is the ideal solution to eliminate algae, mold and outdoor walls and pavements. This powerful cleaner not only removes dirt and blackened caused by dust, pollution and leaf spots, but also thoroughly and cleanses the surfaces, restoring its original appearance.

Advantages

  • Rapid results: It acts effectively in just 15 minutes after the application.
  • Versatile application: Its ideal density allows a uniform application on walls, achieving deep cleaning.
  • Practical format: Available in two formats to adapt to small and large surfaces, facilitating its use in any project.

Ideal for

  • Piedra
  • Mud
  • Brick Vista
  • Extruded sets
  • Painted walls
  • Concrete

Mode of employment

This detergent is ready to use, without the need for dilution.

Instructions:

  1. It previously moistens the surface with water.
  2. Apply the product using the spray, brush or Airless Applicator.
  3. Leave act for 10-15 minutes and rub with a scourer, brush, rotating machine with green disc or pressure water machine.
  4. Rinse with plenty of water. Clean the tools immediately after using them.

Attention

Avoid pulverizing in plants, textiles and metals; In case of contact, clean immediately with water. Do not use new polished stones. On colored cement surfaces, perform a test in a small area to verify possible color changes. Use biocides safely, always reading the label and product information.

Performance

A liter of this product is sufficient to treat between 10 and 20 m², depending on the surface conditions and the application method. The performance is indicative and refers to a single application.

Formats

  • 5 -liter container: Ideal for large surfaces. Available in boxes of 4 units.
  • 500 ml container with sprayer: Perfect for smaller areas. 

Trust the outdoor anti-verdin detergent to maintain your outer and free outer surfaces, prolonging its useful life and maintaining its impeccable appearance.

How much stone do I need?

How much stone do I need for the floor?

For boulders and gravel:
• ±80kg per m², based on a 5cm layer. *For grain sizes >32mm a thicker layer is necessary. • Consumption per bag: 1000kg = 0.625m³.
• Covering capacity: ±12.5m² with a layer of 5 cm.

For pine bark:
• ±70L per m², based on a 5cm layer.
• Consumption per bag: 1000L = ±1m³ = ±600kg
• Covering capacity: ±14m² with a layer of 5 cm.

For volcanic, slate and chamotte:
• ±50kg per m², based on a 5cm layer.
• Consumption per bag: 1000kg = ±1m³
• Covering capacity: ±20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ±1,650kg per 1m³.

The calculation is very easy to understand with an example, if you have a 100x50x30 cm gabion. you have to do the following accounts:
1x0.5x0.3= 0.15m³
0.15x1.650= 247.50kg. of stone.
*It is always good to calculate an extra 5%, since when the gabions are filled they widen a little and there is always a little more stone included than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sieve sizes

The actual sizes may vary slightly, since when we talk about a 60-80mm stone, for example, it means that the stones pass through a 80x80mm square mesh. and they do not pass through a 60x60mm one.
A 100mm stone can pass through that 80x80 mesh. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

stone breaking

On the other hand, in stones larger than 60mm. There is a percentage of up to 10% of stones that can break during classification, washing, loading and unloading. Today we do not have machinery that prevents these breakages.

In the photos you can see, you only see real products, no broken parts have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transportation. This is not a problem when using it; The stone will wash itself over time or you can pour water on it before using it.