Skip to product information
  • "Botella de 750 ml de limpiador instantáneo para juntas de epoxi fresco EPOXY PRO de la marca FILA. Ideal para limpiar gres, cerámica y grandes formatos, así como herramientas después de la aplicación de epoxi. Presentación en spray para una fácil aplicación y rápida acción."
  • Limpiador de juntas en fresco
  • "Etiqueta de advertencia de peligro para EPOXY PRO. Instrucciones de seguridad para el uso de detergente instantáneo para juntas de epoxi fresco, con riesgo de causar irritación ocular grave. Incluye pictograma de riesgo químico y medidas en caso de contacto con los ojos."

EPOXI BOARD CLEANING CLEANING

26,30 €
26,30 €
Tax included. Shipping calculated at checkout.
Container

Description

Instant cleaner for epoxy joint

What is it for?

The instantaneous cleaner for fresh epoxy joints is the perfect solution to remove waste from epoxy joints, both fresh and consolidated, avoiding the formation of the dreaded "opaque veil" that can remain if waste is not completely cleaned. It is ideal for the cleaning of re -jacked tools after use, guaranteeing clean and spots without spots.

Advantages

  • Biodegradable: Formulated with biodegradable ingredients, it is safe for the user and the environment.
  • Rapid Dry Technology: Immediate quick action and drying, ideal for use during the re -jacket phase.
  • Viscous consistency: Perfect for wall cleaning, respecting the material and the joints.
  • High performance: It does not spoil aluminum and steel profiles, and do not create foam.
  • Versatility: Suitable for interiors and exteriors, in pavements and coatings.

Ideal for

  • Porcelain sets
  • Enameled ceramics
  • Vitreous mosaic
  • Enameled extruded sets

Mode of employment

This cleaner is ready to use, without diluting.

Instructions:

  1. Apply the cleaner after rejected, following the instructions of the Board manufacturer.
  2. EPOXY PRO pulverizes in a uniform way on the surface.
  3. Leave on for a few minutes (maximum 2-3 minutes).
  4. Pass a soft sponge without exerting too much pressure, rinseing and draining the sponge.
  5. If cleaning is done after a few hours of the grinding, let the product act for 20 minutes.
  6. Perform cleaning with Epoxy Pro within 24 hours after the reversal. For old epoxy waste, use CR10.

Attention

Always perform a previous test in a small area to verify the resistance of the material and determine the optimal cleaning time. Do not use absorbent materials, wood or metacrylate surfaces. Avoid dripping in unrejunct areas. Test on metal surfaces to ensure its resistance to the product.

Performance

  • Large format pieces: Up to 350 linear meters.
  • Vitreous mosaic: Up to 15 m².

The performance is indicative and may vary according to the application conditions.

Formats

  • 750 ml container with sprayer: Available in boxes of 12 units, designed for an easy and efficient application.

Trust the instantaneous cleaner for fresh epoxy joints to keep your waste impeccable and waste -free, ensuring a perfect finish in your rejar.

Video tutorial

How much stone do I need?

How much stone do I need for the floor?

For boulders and gravel:
• ±80kg per m², based on a 5cm layer. *For grain sizes >32mm a thicker layer is necessary. • Consumption per bag: 1000kg = 0.625m³.
• Covering capacity: ±12.5m² with a layer of 5 cm.

For pine bark:
• ±70L per m², based on a 5cm layer.
• Consumption per bag: 1000L = ±1m³ = ±600kg
• Covering capacity: ±14m² with a layer of 5 cm.

For volcanic, slate and chamotte:
• ±50kg per m², based on a 5cm layer.
• Consumption per bag: 1000kg = ±1m³
• Covering capacity: ±20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ±1,650kg per 1m³.

The calculation is very easy to understand with an example, if you have a 100x50x30 cm gabion. you have to do the following accounts:
1x0.5x0.3= 0.15m³
0.15x1.650= 247.50kg. of stone.
*It is always good to calculate an extra 5%, since when the gabions are filled they widen a little and there is always a little more stone included than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sieve sizes

The actual sizes may vary slightly, since when we talk about a 60-80mm stone, for example, it means that the stones pass through a 80x80mm square mesh. and they do not pass through a 60x60mm one.
A 100mm stone can pass through that 80x80 mesh. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

stone breaking

On the other hand, in stones larger than 60mm. There is a percentage of up to 10% of stones that can break during classification, washing, loading and unloading. Today we do not have machinery that prevents these breakages.

In the photos you can see, you only see real products, no broken parts have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transportation. This is not a problem when using it; The stone will wash itself over time or you can pour water on it before using it.