{"product_id":"grapadora-neumatica-tapicero-grapa-80","title":"Pneumatic upholstery stapler for type 80 staples","description":"\u003cp\u003eUpholstering by hand with a lever stapler tires your wrist and leaves staples half driven in. This \u003cb\u003epneumatic upholstery stapler\u003c\/b\u003e fires each staple with a simple touch of the trigger and leaves it \u003cb\u003eperfectly flush\u003c\/b\u003e in fabric, webbing or plywood, shot after shot and with no effort.\u003c\/p\u003e\n\u003cp\u003eIt works with \u003cb\u003etype 80 staples from 6 to 16 mm\u003c\/b\u003e, the most common in upholstery, and its magazine holds \u003cb\u003e120 staples\u003c\/b\u003e, so you can work your way around a whole seat or headboard without stopping to reload. Supplied in a \u003cb\u003eplastic carry case\u003c\/b\u003e to keep it protected in the workshop or take it on call-outs.\u003c\/p\u003e\n\u003ch2\u003e✅ Key benefits\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eType 80 staples from 6 to 16 mm:\u003c\/b\u003e the standard upholstery format, easy to find in any hardware shop.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003e120-staple magazine:\u003c\/b\u003e fewer stops to reload and a steady working pace.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eClean finish:\u003c\/b\u003e the staple goes in straight and flush, without damaging the fabric or leaving raised points.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eWorks at 4 to 7 bar:\u003c\/b\u003e works with almost any workshop compressor with a regulator.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eCarry case included:\u003c\/b\u003e the tool is protected and always easy to find on the bench or in the van.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e🏗️ What it is for\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eUpholstering chairs, sofas, headboards and vehicle seats.\u003c\/li\u003e\n\u003cli\u003eFixing fabrics, canvas, foams and linings.\u003c\/li\u003e\n\u003cli\u003eFitting elastic webbing to frames.\u003c\/li\u003e\n\u003cli\u003eFixing thin plywood, furniture backs and panels.\u003c\/li\u003e\n\u003cli\u003eDecoration, stage set and display work.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e📋 Technical specifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eStaple type:\u003c\/b\u003e type 80, from 6 to 16 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eStaple width:\u003c\/b\u003e 12.8 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eWire section:\u003c\/b\u003e 0.90 x 0.70 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eMagazine capacity:\u003c\/b\u003e 120 staples\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eWorking pressure:\u003c\/b\u003e 4-7 bar\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003ePower supply:\u003c\/b\u003e compressed air\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003ePresentation:\u003c\/b\u003e plastic carry case\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cblockquote\u003e\u003cp\u003e\u003cb\u003e💡 Vetonek tip:\u003c\/b\u003e adjust the pressure to the material: on thin fabrics lower the pressure so that the staple does not go right through, and on plywood raise it without exceeding 7 bar. Put a few drops of pneumatic oil into the air inlet at the start of the working day and always wear safety glasses.\u003c\/p\u003e\u003c\/blockquote\u003e\n\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\n\u003ch3\u003eWhat staples does it use?\u003c\/h3\u003e\n\u003cp\u003eType 80 staples from 6 to 16 mm long, 12.8 mm wide with 0.90 x 0.70 mm wire.\u003c\/p\u003e\n\u003ch3\u003eWhat is it for?\u003c\/h3\u003e\n\u003cp\u003eFor upholstering, fixing fabrics and foams, fitting elastic webbing and stapling thin plywood or furniture backs.\u003c\/p\u003e\n\u003ch3\u003eWhat pressure does it need?\u003c\/h3\u003e\n\u003cp\u003eIt works between 4 and 7 bar. Adjust the pressure according to the material so that the staple sits flush.\u003c\/p\u003e\n\u003ch3\u003eWhat compressor do I need?\u003c\/h3\u003e\n\u003cp\u003eA stapler uses little air: a small workshop compressor with a pressure regulator and quick coupler is enough.\u003c\/p\u003e\n\u003ch3\u003eHow many staples does the magazine hold?\u003c\/h3\u003e\n\u003cp\u003eThe magazine holds 120 staples, enough to upholster a complete piece without reloading.\u003c\/p\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\":\"https:\/\/schema.org\",\"@type\":\"FAQPage\",\"mainEntity\":[{\"@type\":\"Question\",\"name\":\"What staples does it use?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Type 80 staples from 6 to 16 mm long, 12.8 mm wide with 0.90 x 0.70 mm wire.\"}},{\"@type\":\"Question\",\"name\":\"What is it for?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"For upholstering, fixing fabrics and foams, fitting elastic webbing and stapling thin plywood or furniture backs.\"}},{\"@type\":\"Question\",\"name\":\"What pressure does it need?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"It works between 4 and 7 bar. Adjust the pressure according to the material so that the staple sits flush.\"}},{\"@type\":\"Question\",\"name\":\"What compressor do I need?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"A stapler uses little air: a small workshop compressor with a pressure regulator and quick coupler is enough.\"}},{\"@type\":\"Question\",\"name\":\"How many staples does the magazine hold?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"The magazine holds 120 staples, enough to upholster a complete piece without reloading.\"}}]}\u003c\/script\u003e","brand":"Vica Work","offers":[{"title":"Unit","offer_id":54641432723803,"sku":"CEVIK-R80\/16","price":38.22,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0276\/9698\/8257\/files\/grapadora-neumatica-tapicero-grapa-80-vica-work-1.jpg?v=1793865348","url":"https:\/\/vetonek.com\/en\/products\/grapadora-neumatica-tapicero-grapa-80","provider":"Vetonek","version":"1.0","type":"link"}