Skip to product information
  • Vetonek Set mesa y sillas jardín 3 pzas y cojines ratán sintético gris

Set Table and Garden Chairs 3 pcs and gray synthetic rattan cushions

252,88 €
252,88 € 284,61 €
You save 11% (31,73 €)
Tax included. Shipping calculated at checkout.
Size
Color

Description

This Garden Base Furniture set, elegant design, will become the point of attraction of your garden, terrace or patio. Made of resistant and waterproof Ratán Pe and covered with glass on the board, this exterior dining room set is easy to clean, resistant and adequate for daily use. The steel frame with powder coating causes the table and the chairs to be very resistant and lasting. Thanks to its light construction, all elements are easy to move. The chairs can be stored under the table when they are not being used. The thick and removable cushions of the seat are very comfortable. The cushion covers have zippers and can easily be removed and washed. Note: It is recommended to cover the set in case of rain, snow and frost.

  • Color: gray and anthracite
  • Material: Ratán PE, powder coating steel
  • Cushion material: 100% polyester
  • Table dimensions: 102 x 58 x 76 cm (length x width x high)
  • Chair dimensions: 49 x 52 x 67 cm (wide x high x high)
  • Seat height from the ground: 40 cm
  • Washable cushion cover
  • Requires assembly: Yes
  • Delivery includes:
  • 1 x table with glass surface
  • 2 x chairs
  • 2 x seat cushions
  • 2 x support cushions

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.