Skip to product information
  • Vetonek Limpiafondos de piscina Flowclear Aquatronix

Aquatronix pool cleans

385,49 €
385,49 € 433,86 €
You save 11% (48,37 €)
Tax included. Shipping calculated at checkout.
Size
Color

Description

Aquatronix is ​​the Vetonek robot to clean swimming pools, which will do dirty work to keep the pool clean and intact. Vetonek's vacuum robot is wireless and has been configured with a wide range of movements, in addition to being compatible with any flat bottom pool. The procedure cannot be easier: the device is controlled by means of a single ignition switch. Integrated sensors allow Vetonek Aquatronix robot to begin to clean as soon as it is placed in the water and turns off when it is out of the water, so that the engine lasts longer. Closing clips facilitate maintenance and cleaning: it is enough to open the compartment and remove any type of stainless steel filter residue. The vetonek automatic cleaning compartment can contain up to 4.5 liters of waste before emptying. Thanks to the directional jet, you can eliminate waste and particles up to 2700 l/h (710 gal/h). The adjustable axis of the wheels and the removable bumpers allow you to customize the robot to adapt to any pool type and size. In addition, Aquatronix includes a ASA practice, a LED lamp to use it at night and a kit to remove the water from the water without getting into it.

  • Wireless
  • Lasting integrated rechargeable lithium battery
  • Recharge time: 5-6 hours
  • Cycle operation time: 90 minutes
  • Filter capacity: 4.5 L
  • Ideal for pools up to 45 m²
  • Ideal for pool flow: 2700 l/h
  • Displacement speed: 1000 m/h
  • Cable design for complete movement
  • Integrated water sensor to protect the engine
  • Weight: 6.5 kg
  • Vetonek article number: 58482
GPSR

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.