Skip to product information
  • "Botella de 1 litro de limpiador de residuos epoxi CR10 de la marca FILA. Ideal para eliminar residuos epoxi en superficies verticales como gres, cerámica, y mosaico vidriado. Producto de alta densidad y eficaz para eliminar residuos endurecidos y consistentes. Presentación con asa y tapón de seguridad."
  • "Etiqueta de advertencia de peligro para CR10. Precauciones de seguridad para el uso de limpiador de residuos epoxi, con riesgo de causar irritación ocular grave. Incluye pictogramas de riesgo químico y medidas a seguir en caso de contacto con los ojos."

Epoxy waste cleaner

28,30 €
28,30 €
Tax included. Shipping calculated at checkout.
Container

Description

Epoxy waste cleaners Row: Deep and effective surface cleaning

What is it for?

The epoxy waste cleaners is a high viscosity liquid detergent designed specifically for the elimination of waste, spots and epoxy and resinous joint fences. It is ideal for low absorption materials such as porcelain, ceramic, enameled and vitreous mosaic (gresite), guaranteeing effective and safe cleaning.

Advantages

  • Effective elimination: Thanks to its density, it effectively eliminates spots, fences and waste from epoxy joints, even in cases of hardened waste.
  • Respect for materials: Clean deeply without damaging the treated surfaces.
  • Easy application: Its liquid formula allows simple and fast application.
  • Nice perfume: Nice almond aroma that leaves a fresh smell after cleaning.

Ideal for

  • Extruded sets
  • Ceramics and enameled sets
  • Vitreous mosaic (gresite)
  • Extusing enameled

Mode of employment

This cleaner should be used pure, without dilution.

Instructions:

  1. Stir the container well before using.
  2. To remove hardened joint waste, apply the pure cleaner with a brush and leave on for 30 minutes.
  3. Rub the surface with a scourer or, in case of more consistent waste, use a spatula. In pavements, it is possible to use a rotating machine with an adequate disk.
  4. Clarifies abundantly with water. If the waste persists, repeat the operation by leaving the product for longer.

Attention

It is advisable to perform a previous test in a small area to check the resistance of the material and determine the optimal cleaning time. Do not use this product in absorbent materials, wood or metacrylate surfaces. On metal surfaces, previously proves the resistance of the material to the cleaner.

Performance

A liter of this product is sufficient to treat up to 10 m², depending on the amount and consistency of the residue. Performance is indicative.

Formats

  • 1 liter container: Available in boxes of 12 units, ideal for comfortable and efficient use.

Trust the epoxy waste cleaners for deep and safe cleaning of surfaces with epoxy joints, maintaining its impeccable appearance and prolonging its useful life.

Video tutorial

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.