Skip to product information
  • Vetonek Sillón de masaje reclinable de tela verde

Green cloth reclining massage chair

267,63 €
267,63 € 301,21 €
You save 11% (33,58 €)
Tax included. Shipping calculated at checkout.
Size
Color

Description

This specially designed massage reclining chair is an excellent seat solution and a perfect contribution to your living room. The electric massage chair is made of cloth and has wooden legs, which makes it strong and soft to sit. The armchair has 6 back massage points, seat and legs. The included manual control allows you to choose different massage programs. Just by pressing the button, the seat can also be heated for an additional sense of relaxation. In addition, the backrest can be adjusted backwards, while the restraint can be adjusted up. This position allows you to sleep comfortably. This reclining electrical massage chair is also equipped with a side pocket to save the remote controls. Note: The product has a USB connector, but the Certified 5V USB supply source is not included.

  • Color: Green
  • Material: fabric (100% polyester), rubber wood
  • Total dimensions: 71 x 90.5 x 101.5 cm (wide x high x high)
  • Total dimensions (reclined): 71 x 132.5 x 86 cm (wide x high x high)
  • Dimensions of the chair: 50 x 53 cm (deep x width)
  • Seat height from the floor: 53 cm
  • AJUSTABLE REPATIS AND BACK
  • Options: massage and heat
  • Massage type: 6 -point vibration massage
  • Requires assembly: Yes
This product works with 5 V CC, but the 5 V certified USB supply source is not included. High voltage can cause overheating and can cause damage to the device and the potential risk of overheating and fire.

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.