Diamond-Point Pillar Cap - End Piece with Drip Edge for Chimneys
Diamond-Point Pillar Cap: what it is
The diamond-point pillar cap is the four-slope end piece that caps pillars and chimneys. Its built-in drip edge stops water getting in and the slope on all four faces minimises dirt build-up on top, so the whole thing stays clean and functional.
✅ Key advantages
Four-slope profile: water drains off all four sides and doesn't pool on the piece.
Built-in drip edge: optimal water drainage and protection for the pillar's exposed face.
Three sizes: 28 × 28, 40 × 40 and 50 × 50 cm, covering everything from a narrow chimney to a 40 cm pillar.
Less maintenance: the slope sheds dust and leaves, so the top of the pillar gets far less dirty.
Colours: white and beige, matching the Bellver pillar and block and the Loarre pillar.
🏗️ Recommended applications
Capping chimneys and exposed-brick flues.
Capping fence pillars and plot enclosures.
Capping gate and entrance piers.
Finishing buttresses in garden walls.
Capping pillars for porches and built pergolas.
📋 Technical data sheet
Material: strong, durable concrete.
Design: diamond point with built-in drip edge for optimal water drainage.
Dimensions: 28 × 28 × 3.5 × 7 cm, 40 × 40 × 5.5 × 9 cm and 50 × 50 × 6 × 10 cm.
Colours available: white and beige.
Units per pallet (28 × 28 × 3.5 × 7 cm): 24 units.
Units per pallet (40 × 40 × 5.5 × 9 cm): 24 units.
Units per pallet (50 × 50 × 6 × 10 cm): 14 units.
🧰 Installation
Finish the pillar or chimney with the last course flush and let it cure before capping it.
Clean the top and check the level in both directions.
Dry-fit the piece and spread the overhang evenly on all four sides; leave 3 to 5 cm per side.
Apply concrete-paver adhesive in interior beads, without reaching into the drip-edge groove.
Bed with a rubber mallet and check the level again before the adhesive grabs.
Remove any material that spills over the perimeter while fresh.
📦 Available formats
28 × 28 × 3.5 × 7 cm — white or beige — single unit or pallet of 24.
40 × 40 × 5.5 × 9 cm — white or beige — single unit or pallet of 24.
50 × 50 × 6 × 10 cm — white or beige — single unit or pallet of 14.
💡 Professional tip: for chimneys, measure the flue before ordering, not the brick pillar: the piece needs to overhang past the cladding, not sit flush with it. If the cap doesn't project at least 3 cm on each side, water runs straight down the face, the drip-edge groove doesn't do its job, and vertical stains appear below the cap by the first winter.
Frequently Asked Questions
¿Sirve para rematar chimeneas?
Sí. Es su aplicación principal: evita la infiltración de agua y reduce la acumulación de suciedad en la parte superior.
¿Qué medidas hay disponibles?
28 × 28 × 3,5 × 7 cm, 40 × 40 × 5,5 × 9 cm y 50 × 50 × 6 × 10 cm.
¿En qué colores se fabrica?
En blanco y en beige.
¿Cuántas unidades trae el palet?
24 unidades en las medidas de 28 y 40 cm, y 14 unidades en la de 50 cm.
¿Para qué sirve el goterón?
Para que el agua se despegue del canto y no escurra por la cara vista del pilar o de la chimenea.
¿Cuánto vuelo debo dejar?
Entre 3 y 5 cm por cada lado, repartidos por igual.
¿Con qué pilares combina?
Comparte colores con el pilar y el bloque Bellver y con el pilar Loarre, y existe también en versión plana.
¿Con qué se fija?
Con adhesivo para prefabricados de hormigón aplicado en cordones interiores.
