Cubre las jardineras con facilidad, retiene el agua y es muy grato a la vista.
Jara L-Shaped Pool Coping - High-Compaction Concrete
19,05 €
19,05 €
Tax included.
Shipping calculated at checkout.
Jara L-Shaped Pool Coping - High-Compaction Concrete
Jara L-Shaped Pool Coping: the profile that holds the liner and hides the build
Fitting a liner or a lining in a built pool shell always leaves an irregular top edge that needs hiding. The Jara coping has an L-shaped section that houses the liner's anchor track and hides the edge's imperfections, in a high-compaction concrete that reaches USRV 80, the highest slip rating in the whole family.
✅ Key advantages
- L-profile: makes fitting the liner and other linings easier, and hides the pool shell's top edge.
- USRV 80, class 3: the best grip in the range, tested on the piece itself, not extrapolated from paving.
- High-compaction concrete: less porosity, less water absorption and better behaviour against ice.
- Bevelled edges: the bevel matches the paving in the same range and avoids a sharp edge that chips.
- Four colours: white, anthracite, sand and bronze, from lightest to darkest.
- Two sizes: 50 × 35.5 cm for a standard perimeter and 46 × 50 cm when a wider edge is wanted.
🏗️ Recommended applications
- Capping built-in pools finished with a liner.
- Pool edges with mosaic tile or a reinforced membrane, where the top anchor track is exposed.
- Coping for renovated shells with an irregular top edge.
- Contemporary-design pools, matching the bevelled paving in the same range.
- Capping ornamental ponds and water features that are walked on.
📋 Technical data sheet
- Material: high-compaction concrete.
- Profile: L-shaped section with bevelled edges.
- Slip resistance: USRV 80, Class 3.
- Weight per unit (50 × 35.5 cm): 17 kg.
- Dimensions: 50 × 35.5 × 31.5 × 4.5 × 6 cm and 46 × 50 × 4.5 × 6 cm.
- Colours: white, anthracite, sand and bronze.
- Units per pallet: 50 × 35.5 cm: 60 units · 46 × 50 cm: 70 units.
- Weight of a pallet of 60 units: 1,032 kg.
- Use: outdoor, at the water's edge.
🧰 Installation
- Have the liner and its anchor track fitted and tensioned before laying the coping; the housing isn't accessible afterwards.
- Level the pool shell's top edge: with an L-profile, any high spot stops the piece sitting flat.
- Bed with a C2 cement-based adhesive rated for outdoor and immersion use, double-buttered, also bonding the vertical face of the L.
- Keep a 1.5-2% fall towards the outside along the whole perimeter.
- Leave a 3-5 mm joint between pieces and an elastic expansion joint every 4-5 m and at every corner.
- Point with an outdoor-rated mortar and seal the joint against the pool shell with polyurethane sealant.
📦 Available formats
- 50 × 35.5 × 31.5 × 4.5 × 6 cm — single unit or pallet of 60 units.
- 46 × 50 × 4.5 × 6 cm — single unit or pallet of 70 units.
- Both sizes in white, anthracite, sand and bronze.
💡 Professional tip: the order of work is what decides whether this piece works. The liner and its anchor track always go in first: fit the coping before that and the L's housing becomes inaccessible, meaning already-bonded pieces have to be lifted. Bond the vertical face of the L too, not just the horizontal one; left hollow, water gets between the coping and the shell, freezes in winter and pops the piece off. And don't mistake USRV 80 for a free pass: it's an excellent rating, but this is still a pool coping, not a paving slab, so it needs an immersion-rated adhesive, an outward fall and an expansion joint against the surround slab. Order 8-10% extra material: in a high-compaction concrete, disc-cutting is slower and the cut isn't as clean as it looks.
Frequently Asked Questions
¿Para qué sirve el perfil en L?
Aloja el anclaje del liner o del revestimiento y oculta el remate superior del vaso, que en una piscina de obra nunca queda recto.
¿Qué va primero, el liner o el remate?
El liner y su perfil de anclaje, siempre. Si coloca el remate antes, el alojamiento de la L queda inaccesible.
¿Hay que encolar la cara vertical de la L?
Sí. Si queda hueca, entra agua entre el remate y el vaso, hiela en invierno y desprende la pieza.
¿Qué significa USRV 80?
Es el valor de resistencia al deslizamiento, el más alto de esta familia de productos, y corresponde a clase 3. Está medido sobre la propia pieza.
¿Qué aporta el hormigón de alta compactación?
Menos porosidad, menos absorción de agua y mejor comportamiento frente a los ciclos de hielo-deshielo.
¿Qué adhesivo hay que usar?
Cemento cola C2 apto para exterior e inmersión, en doble encolado.
¿Qué medida elijo?
La de 50 × 35,5 cm para el perímetro corriente; la de 46 × 50 cm cuando se busca un borde más ancho.
¿Cuánto material de más conviene pedir?
Entre un 8 y un 10 %. Cortar hormigón de alta compactación a disco es lento y el corte no queda tan limpio como parece.