High temperature plants protector
¿Cuanto material necesitas?
¿Cuanto material necesitas?
How much stone do I need?
How much stone do I need for the ground?
For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.
For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.
For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm
How much stone do I need to fill a gabion?
Density of ± 1,650kg by 1m³.
The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.
Clarifications
ATTENTION!
Granulometries are sizes of sizes
Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.
Broken stones
On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.
In the photos you can see, only real products are seen, broken pieces have been removed.
Dust and sand in products
This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.
High temperature plants protector
Product formulated based on clay (kaolin, white clay) that can be used to reduce the harmful effects caused by high temperatures in plants and crops. It is the "agricultural refractory clay", which is applied in the form of dust on the leaves and stems of the plants.
Agricultural refractory clay is a natural and non -toxic product that is used to improve the resistance of plants to thermal stress and heat stroke. This clay helps reduce the surface temperature of the plant, which in turn reduces the evaporation of water and increases efficiency in the use of water resources.
The application of agricultural refractory clay can also help prevent the loss of nutrients and dehydration of plants in warm and dry climates. In addition, clay can act as a physical barrier against UV rays, protecting plants from the harmful effects of solar radiation.
Caolin application to reduce high temperatures damage
This is how you should apply refractory clay in woody and extensive crops to protect them from thermal stress and heat stroke. A general dose of 4-6 kg/hl is recommended in woody crops and a minimum of 40 kg/ha, and a 30 kg/ha dose in extensive crops such as industry, cotton and pepper tomato. Subsequent maintenance applications can be made at a dose of 3 kg/hl.
The preparation of the broth is done by gradually adding the product to the cuba of treatments and filling the tank up to 80% of its volume. It is recommended that the agitation system be in operation throughout the application. Mojantes can be added if necessary.
Precautions must be taken and postpone the application in case of wind or risk of rains, and clean the atomizer after use. The product should not be applied to fruits that cannot be washed, brushed and fogged in the post harvest. Caolin traces in treated fruits after collection do not affect quality.