Skip to product information
  • RIDDER Alfombrilla de ducha Zebra blanco y negro 54x54 cm

RIDDER Shower mat Zebra Black and white 54x54 cm

37,62 €
37,62 € 42,34 €
You save 11% (4,72 €)
Tax included. Shipping calculated at checkout.
Size
Color

Description

Ridder's Zebra shower mat reduces the risk of slips and injuries when leaving or entering the bathtub. Great quality: The shower mat is made 100% tpe respectful of the skin. The insert has no latex, BPA, phthalates or PVC, so there is no risk of contact allergies. In addition, the material and the manufacturing process are thoroughly controlled and tested by the Tüv. Non -slip design: the carpets do not move thanks to the 126 suction cups of the reverse. Therefore, the rubber carpet is valid for babies, children, adults, elders and animals. Virtually no waste is generated during production. The heat generated by the machine is also used for the heating of the company. Cleaning Fácil: The rubber carpet is easy to clean and maintain. It must be rinsed well with water after each use. Carombrillas can also wash in the washing machine at 30 ° C with a soft cycle. Note: Wash separately and not centrifuge. Note: The adhesion of the suction cups can be affected by irregular surfaces or in the case of bathtubs with porous enamel. Solvents, bathing or soap can form a slippery movie on the surface.

  • Color: White
  • Printed color: black
  • Material: 100% tpe
  • Dimensions: 54 x 54 cm (width x long)
  • Tested by Tüv
  • Non -slip
  • Manufactured in Germany
  • Sustainable and recyclable

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.