Skip to product information
  • Kit de compresión de muelles Mercedes 5 piezas

Mercedes dock compression kit 5 pieces

137,10 €
137,10 € 154,31 €
You save 11% (17,21 €)
Tax included. Shipping calculated at checkout.

Description

This telescopic spring compressor for universal use has a special non -slip design and three reinforced arms for a maximum grip. This kit allows you to disassemble and replace the helical docks of the fork without disassembling the axis, thus saving a valuable time and money. It can also be used in independent suspensions of several links. The game is supplied with two pressure plates sizes. It covers the vast majority of modern vehicles, including: large pressure plate: Mercedes-Benz W123, W124, W202, W210 Front Axle and W124, W129, W201, W202 Rear Axle In addition to some SAAB, Ford and Scoda; Small pressure plate: Mercedes-Benz W126, W140, W100, W200 and rear axle W107, W114, W115, W116, W123, W126, W140, W203. More some GM, Opel, Peugeot (406, 605), Rover, Hyundai, Saab, Volvo, Volkswagen, Fiat, Mazda, Toyota, Nissan, Mitsubishi, Ford Lada. The dock compressor kit is agreed with the high quality standard. It is suitable for both fans and professional users.

  • 2 x spring clamp sets
  • 1 x telescopic compressor
  • Maximum dock load: 1250kg
  • Adaptation: diameter 80 mm -135mm
  • Gloan opening: 115-300 mm
  • Unit: 19 mm Hexagonal
  • Dimensions: 45 x 31 x 9.5 cm (length x width x high)

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.