Skip to product information
  • Vetonek Soporte para pesas y mancuernas

Weight and dumbbell support

162,83 €
162,83 € 183,26 €
You save 11% (20,43 €)
Tax included. Shipping calculated at checkout.
Size
Color

Description

This support of dumbbells and weights is designed to place weights, dumbbells and bars organized on and off the ground. It adapts to most sizes and styles of dumbbells, including neoprene and cast iron. The stable structure and the two shelves will help you maintain a cleaner home gym environment by providing a place to park their weights when they are not in use. It is made of resistant steel for years of use. The anti -slip rubber base helps protect the damage ground and guarantees optimal stability and safety. This shelf with its resistant construction has a maximum load of 300 kg. It is also suitable for almost all weights of weights. It measures 49 percent by 95 cm when it is completely mounted.

  • Dimensions: 49 x 100 x 95 cm (length x width x high)
  • Maximum load: 300 kg.
  • Gray
  • 7 round tubes
  • 8 supports (4 supports on each side)
  • Bar diameter: 25 mm
Read the manual carefully before using the product. The product is a home fitness device. If it is under treatment due to heart problems, blood pressure, high cholesterol, etc., it is very important to consult a doctor before training. Always pay attention to your health status before training. Incorrect training methods can cause health problems. Stop training if you have any discomfort, such as headache, chest oppression, irregular heart rate, difficulty breathing, dizziness and nausea, etc.

How much stone do I need?

How much stone do I need for the ground?

For shot and gravel song:
• ± 80kg per m², based on a 5cm layer.*For granulometries> 32mm a thicker layer is necessary.• Saca consumption: 1000kg = 0.625m³.
• Covering capacity: ± 12.5m² with a layer of 5 cm.

For pine cortex:
• ± 70L per m², based on a 5cm layer.
• Saca consumption: 1000L = ± 1m³ = ± 600kg
• Covering capacity: ± 14m² with a layer of 5 cm.

For volcanic, slate and chamota:
• ± 50kg per m², based on a 5cm layer.
• Saca consumption: 1000kg = ± 1m³
• Covering capacity: ± 20m² with a layer of 5 cm

How much stone do I need to fill a gabion?

Density of ± 1,650kg by 1m³.

The calculation is very simple to understand with an example, if you have a 100x50x30 cm gav. You have to make the following accounts:
1x0.5x0,3 = 0.15m³
0.15x1,650 = 247.50kg. stone.
*It is always good to calculate an extra 5%, since the gavions when filling them are a little and always enters some more stone than in the theoretical calculations.

Clarifications

ATTENTION!

Granulometries are sizes of sizes

Real sizes can vary slightly, since when talking, for example, 60-80mm stone, it means that the stones pass through a square mesh of 80x80mm. and do not go through a 60x60mm.
This 80x80 mesh can pass a 100mm stone. long and 65mm. wide so there may be a percentage of stones greater than 80 and less than 60mm.

Broken stones

On the other hand, in the stones of more than 60mm. There is a percentage of up to 10% stones that can be broken during classification, washing, loading and downloading, today we have no machinery that avoids those breaks.

In the photos you can see, only real products are seen, broken pieces have been removed.

Dust and sand in products

This product is not washed, so it contains dust, sand and even traces of other products due to processing and transport. This is not a problem when using it; The stone will be washed alone over time or can throw water before using it.